Tag Archives: Santa

Santa’s Workshop

Posted on by .

When you enjoy DIY or have some skills, there is no better gift than a homemade gift right? It's more personal, carries more meaning. But at what cost? It has been awhile since my last post, and that is because I have been busy in Santa's workshop. In my case, that's my garage, or to be more accurate, half my garage. The other half is storage. I've never had a car in my garage, at any house. One day when I have a separate workshop and a basement for storage, I might park cars in the garage. But until that day, the cars are relegated to the driveway. At our house, the garage is the main point of entry. It leads into the mud room/hallway where shoes, bags and jackets can be deposited. But when Santa's Workshop is open for business, the garage is closed. All traffic must go through the front door. That also means that I have to get anything that is needed from the garage. This year's present was much too large to just cover with a tarp. It required complete exclusion from garage access.

You know from my previous post that I have a whole stack of barnwood harvested from a local barn. Well, that wood won't do me any good just sitting there will it? Combine a stack of barn wood with Christmas and I have my work cut out for me. When we were first married, I made a kitchen table with a folding butterfly leaf. Our family grew quickly so we never really had the leaf closed up. The table just fit the six of us with no room to spare. It was time to grow and get a table more fitting for our family size. Also, I was never really happy with the previous table top. The table was maple and cherry and I really liked how the legs turned out, but for the top I tried to save money by layering maple on top of plywood. It just never worked out right. I refinished it a few years ago which helped some, but it still bugged me every time I sat down to eat.

Barn wood is great because it is aged and dried. You know there will be no more warping. But that also means the pieces are already warped and misshapened. If I had a planer and jointer, that wouldn't be a problem, but alas I do not. The edges were already rabbeted so using pipe clamps I glued the table top together. No matter how many clamps I used, I couldn't quite get every board to lay flush, but with some cross pieces screwed in from underneath, I could pull all of the boards securely together.

The apron required ripping the boards to width so I used the table saw as sort of a poor man's jointer. The legs are made from a 2×6 board from the barn secured to the apron with corner braces and bolts. It all went together square, but did not keep the table from rocking back and forth. I needed some angled braces for that. One end of the braces is bolted to the legs with a hex bolt going all the way through the leg. For the apron end, I chiseled out an insert for the brace so the actual apron would keep it from sliding or moving. It was then attached by a straight metal brace. It looks great and works really well.

I also decided to build a bench for one side of the table. We always seem to be pulling the piano bench in when we are feeding the neighbor kids or friends so why not just build one up front? You can cram more kids onto a bench than you can individual chairs. I used the same method for the top of the bench and then cut two pieces of a beam for the legs. A 2×6 support goes length wise down the center of the bench and rests on the legs in a cut out notch. I had to use my reciprocating saw to cut the beam for the legs, but just cut the notch on the table saw and cleaned it up with a chisel. The beam is secured to the support brace by a long hex bolt going all the way through.

 

With the table and bench built and ready for finishing I proceeded to blanket the entire garage in fine sanding dust. Every box, shoes, tools, bikes, everything had a fine coat of dust. I didn't sand everything perfectly smooth except for the top. I still want it to look a bit rough like barn wood should. I used a satin polyurethane finish sprayed onto the underside of the table top, the apron, legs, and the bench. Three coats were enough to provide a good solid finish. Then came the adventure of the tabletop.

I wanted a thick finish that filled in all holes and cracks and could also smooth out any uneven spots of the tabletop. You don't want to be sliding a glass of milk across your table just to have it crash when hitting a seam in the wood. And you don't want liquid spills drying in the cracks between boards. Using an epoxy resin, which is very expensive, I coated the table top. I had to take over one of the kid's rooms because it is too cold out in the garage for the epoxy to cure completely. I set up a tarp and a folding table in the room. Come to find out there were lots of seams in the table top not necessarily visible to the naked eye. I ended up having to buy another box of epoxy for the second coat because so much was running through the cracks and off the edges. Once the first coat dried and sealed things up, I applied the second smoothing coat and let that dry.

The following morning when I attempted to lift the new table top off the folding table, I found it was stuck, completely epoxied to the table! I tried prying it off with a pry bar, tried to saw through it, and tried a chisel. Nothing worked. The two tables had become one. I ended up having to use my Dremel to cut out holes in the folding table and then cutting down the edges to match the perpendicular supports. The epoxy and top layer of the folding table are there to stay, adding some great strength to my tabletop. The folding table on the other hand has two giant gaping holes in it and will have to be resurfaced with plywood or something. You should have seen my wife's face when she saw the folding table!

I woke up early Christmas morning as I always do and hefted the tabletop downstairs to assemble everything in the dining area. When everyone came downstairs, it took a moment for her to notice a new table just sitting there, but when she did it was a huge hit! The barn wood looks great and the table fits our family much better. However, Santa's Workshop will be closed for the foreseeable future. It's time to spend my evenings inside rather than out in the garage.

Keep checking my YouTube channel for the how to video. I am still working on editing and putting it together.

Update. Here is the video! It's a little long, but it was a big project. Enjoy!